How to Pair Your LoveHandle Pro with a Camera Lens Protector for All-Day Protection

Your phone is your everyday companion, and you've invested in both a LoveHandle Pro for a secure grip and a camera lens protector to keep those precious photos sharp. But can they work together without causing problems? The short answer is yes — with a little planning and the right installation order.

In this guide, I'll walk you through exactly how to pair your phone grip and lens protector so both stay put, your camera stays clear, and your LoveHandle Pro stays firmly attached. Whether you're using a LoveHandle PRO for MagSafe – Lady of the Sea or a classic PRO – Tongue Tied, these tips will help you get the best of both accessories.

Why Pairing a Phone Grip and Lens Protector Needs Careful Planning

A camera lens protector adds a thin layer of glass or tempered film over your phone's rear lenses. It's designed to guard against scratches and cracks without affecting photo quality. Meanwhile, a LoveHandle Pro relies on a strong adhesive pad or MagSafe connection to stay attached to your phone's back. If you place the grip too close to the lens protector's edge, the adhesive might not seat flat, or the grip could push against the protector and cause it to lift.

The good news is that most LoveHandle Pro models, including the LoveHandle PRO for MagSafe – Reds Fan Edition, are designed to sit away from the camera module. But if your phone has a large camera bump or a multi-lens array, you'll want to double-check clearance. A simple rule: keep at least 3–5 mm of space between the grip's base and the lens protector's outer edge.

• If your lens protector has a raised metal ring, ensure the LoveHandle Pro adhesive pad doesn't overlap it.
• For MagSafe models, the magnetic ring is centered — so lens protectors on the left side of the phone usually won't interfere.

Step-by-Step: Installing a LoveHandle Pro with a Camera Lens Protector

Start by cleaning your phone's back thoroughly with the included alcohol wipe. If you already have a lens protector installed, remove it temporarily — this gives you a clean surface to position the grip. Place the LoveHandle Pro on the phone without peeling the adhesive liner to test alignment. Make sure it sits comfortably in your hand and doesn't press against the lens protector area.

Once you're happy with the position, peel the liner and press the grip firmly for about 30 seconds. Let it cure for 24 hours before attaching the lens protector. This curing time allows the adhesive to bond fully. After that, apply the lens protector according to its instructions, taking care not to touch the grip's edge. For a seamless look, choose a lens protector that's slightly smaller than the camera bump so it doesn't extend into the grip's zone.

• Use a microfiber cloth between steps to avoid dust getting trapped under the lens protector.
• If you're using a PRO Swappable Strap, the base stays on — so you only need to align it once.

What to Do If You Already Have Both Installed and They're Interfering

Sometimes you install a lens protector first and then realize the LoveHandle Pro is nudging it. If the grip is removable (non-MagSafe models), gently peel it off using a thin plastic card or the included removal tool. Clean the adhesive with a lint-free cloth and reposition it slightly higher or lower. For MagSafe versions like the LoveHandle PRO for MagSafe – Honeyed Blooms, the magnetic ring holds it in place — so you can rotate or shift it without losing adhesion.

If the lens protector is the one causing trouble, consider switching to a thinner version or one without a metal rim. Some thick protectors create a hump that lifts the grip's edge. In that case, a low-profile lens protector that sits flush with the camera bump works best. Remember, the goal is all-day protection without sacrificing comfort or photo quality.

• Avoid using rubbing alcohol on the lens protector — it can damage the anti-reflective coating.
• Test the grip's hold by gently wiggling it after repositioning; if it feels loose, let it cure again.

Pairing a LoveHandle Pro with a camera lens protector is totally doable — you just need to plan the installation order and leave a little breathing room. Start with the grip, let it cure, then add the lens protector. Whether you're rocking a PRO – Confetti or a LoveHandle PRO for MagSafe – Reds Fan Edition, this approach keeps both accessories secure and your phone protected from every angle.